Search found 15 matches

by yisabell
Thu Apr 18, 2019 11:54 pm
Forum: Version 2.58
Topic: New compile if GRBL 1.1g on IDE 1.8.8
Replies: 13
Views: 1448

Re: New compile if GRBL 1.1g on IDE 1.8.8

I did not unplug all the wires off of the hat.

Is that a requirement of the compile and upload?
by yisabell
Thu Apr 18, 2019 11:47 pm
Forum: Version 2.58
Topic: PWM connection
Replies: 13
Views: 1003

Re: PWM connection

There are many article on how to convert PWM to resistance. I would explore how the pot fits in with the controller circuit first.
Here is one example I found on Google.

https://electronics.stackexchange.com/q ... resistance

Good luck.
by yisabell
Thu Apr 18, 2019 9:23 pm
Forum: Current Version(2.60)
Topic: Howto: Use software that only works over USB/serial
Replies: 5
Views: 563

Re: Howto: Use software that only works over USB/serial

I use lightburn all the time now. Its my go to software, but I cannot get the ser2net connection to work. I would be a game changer if we could make that work. But ser2net has be around for some time and version changes can and do cause incompatibilities. So if someone has a working version, I am al...
by yisabell
Wed Mar 20, 2019 9:32 pm
Forum: Version 2.58
Topic: New compile if GRBL 1.1g on IDE 1.8.8
Replies: 13
Views: 1448

Re: New compile if GRBL 1.1g on IDE 1.8.8

Yes the configuration on the PI and hat are working. I have bCNC running ok. But for some reason it wont upload. I have tried to reset the hat but to no avail. My board selection is Arduino/Genuino Uno. Port is /dev/ttyAMA0. I may try downloading a new copy of GRBL in case of some corruption but I a...
by yisabell
Sun Mar 17, 2019 3:25 pm
Forum: Version 2.58
Topic: New compile if GRBL 1.1g on IDE 1.8.8
Replies: 13
Views: 1448

Re: New compile if GRBL 1.1g on IDE 1.8.8

GRBL is on the PI and all is working, but I merely need to recompile to make a few change to the two files above.
by yisabell
Wed Mar 13, 2019 1:31 am
Forum: Version 2.58
Topic: New compile if GRBL 1.1g on IDE 1.8.8
Replies: 13
Views: 1448

Re: New compile if GRBL 1.1g on IDE 1.8.8

This was done on the PI. The upload to the Arduino on the controller keep failing for some reason.

I have done this before but this time it fails per the messages above.
by yisabell
Fri Mar 08, 2019 10:22 pm
Forum: Version 2.58
Topic: New compile if GRBL 1.1g on IDE 1.8.8
Replies: 13
Views: 1448

Re: New compile if GRBL 1.1g on IDE 1.8.8

My whole reason to recompile/upload was to make some mods in the config.h and CPU_MAP.h.

How can I make those changes using a generic hex file.

Is there something I am missing.

Thanks for the response.

Yves...
by yisabell
Sun Mar 03, 2019 1:12 am
Forum: Version 2.58
Topic: New compile if GRBL 1.1g on IDE 1.8.8
Replies: 13
Views: 1448

New compile if GRBL 1.1g on IDE 1.8.8

I have been at this for days and in a nutshell here is the process I have followed per (https://github.com/grbl/grbl/wiki/Compiling-Grbl): - downloaded and installed Arduino IDE 1.8.8 (all is fine and working) - downloaded GRBL 1.1g as a ZIP file and extracted - Ran IDE and loaded library GRBL (stil...
by yisabell
Mon Feb 18, 2019 1:06 am
Forum: Current Version(2.60)
Topic: Howto: Use software that only works over USB/serial
Replies: 5
Views: 563

Re: Howto: Use software that only works over USB/serial

I see that LightBurn has a Linux version, does anyone know if that will work on the PI with the Protoneer controller?
by yisabell
Thu Jun 14, 2018 9:56 pm
Forum: Version 2.58
Topic: RPI 3 B with v2.58 hat
Replies: 4
Views: 612

Re: RPI 3 B with v2.58 hat

No I Did not...i just gave up and recreated the image.

But I will keep that in mind next time.

Does the touchscreen conflict with controller access?