Search found 1779 matches

by Bertus Kruger
Fri May 21, 2021 1:05 am
Forum: Current Version(2.60)
Topic: Headless bCNC operation
Replies: 3
Views: 1447

Re: Headless bCNC operation

bCNC needs a screen to operate. So it will need to be VNC and it will only be able to run after connecting.

Not sure if Linux has a way to do that....
by Bertus Kruger
Fri May 21, 2021 1:01 am
Forum: Current Version(2.60)
Topic: Hold Abort Rest Resume Direct Wiring
Replies: 1
Views: 462

Re: Hold Abort Rest Resume Direct Wiring

questmechanics wrote:
Mon Apr 26, 2021 8:35 am
Is it possible to directly wire E-Stop and control panel buttons to the RST, ABORT, RESUME and HOLD buttons on the shield? Thanks in advance.
Yes... it should be okay. Shorting the pin to GND will activate their function
by Bertus Kruger
Fri May 21, 2021 12:59 am
Forum: Current Version(2.60)
Topic: 7 in touchscreen power supply
Replies: 1
Views: 449

Re: 7 in touchscreen power supply

I have a v. 2.60 with rpi and the 7 in touchscreen. Since the Protoneer hat uses the power GPIO pins, how are others powering their touchscreen? Use one of the USB outputs from the rpi to the micro usb port on the touchscreen control board? With a good USB power supply like the 3A RPi power adapter...
by Bertus Kruger
Sun Apr 25, 2021 9:44 pm
Forum: Current Version(2.60)
Topic: Raspberry Pi 4 Model B - External drivers TB6560 - No movement
Replies: 4
Views: 598

Re: Raspberry Pi 4 Model B - no life sign from the motors

From your email this the unit you are using... TB6560.gif This particular driver looks like the 5V pin is powering an optocopulare of some kind and can be using a bit of current on the 5V pin. (Some of these drivers also don't need the Enable pin connected because they have a pull up resistor. )
by Bertus Kruger
Sun Apr 25, 2021 9:42 pm
Forum: Current Version(2.60)
Topic: Raspberry Pi 4 Model B - External drivers TB6560 - No movement
Replies: 4
Views: 598

Re: Raspberry Pi 4 Model B - no life sign from the motors

This is what I would try. wire.png The reason for the External 5V source is because I am not sure how much current the stepper driver is using on the 5V pin. I have suggest tying the Enable pin to the 5V pin while we try to get the external drivers moving. (My suspicion is that the enable pin is the...
by Bertus Kruger
Sun Apr 25, 2021 9:34 pm
Forum: Current Version(2.60)
Topic: Raspberry Pi 4 Model B - External drivers TB6560 - No movement
Replies: 4
Views: 598

Re: Raspberry Pi 4 Model B - no life sign from the motors

From your email this the unit you are using...
TB6560.gif
TB6560.gif (391.06 KiB) Viewed 593 times
by Bertus Kruger
Fri Apr 16, 2021 9:04 am
Forum: Current Version(2.60)
Topic: Another rebuild
Replies: 10
Views: 1521

Re: Another rebuild

AN update, so far I have the gantry frame built, ready for the Z and X rails to be fitted, also have the X Z base plate built with bearings and the spindle bracket. Probably will not get back to it until after Easter. Hoping that Bertus has made progress on the 5 axis board. :D Slowly but surely......
by Bertus Kruger
Fri Apr 16, 2021 8:59 am
Forum: Current Version(2.60)
Topic: Power supply for Pi Hat
Replies: 1
Views: 503

Re: Power supply for Pi Hat

Hi All, New to Pi Hat, so hoping someone might help me. I have Neam23 drivers with 48v power supply. Pi Hat can accept 12-36v. Pi Hat requires power in order for arduino chip to be powered. So do I need stepdown converter for 48v to be down to 12/24v? Or is there another around that? Thank you, XDe...
by Bertus Kruger
Fri Apr 16, 2021 8:55 am
Forum: Current Version(2.60)
Topic: Grove Connector I2C SDA and SCL pins are flipped
Replies: 4
Views: 1085

Re: Grove Connector I2C SDA and SCL pins are flipped

maxomous wrote:
Fri Apr 09, 2021 1:47 pm
Just signed up to say that I found this problem, but you've beaten me to it.

You say you're removing the connector? Are the leaving the pads in place on the PCB so a user can still add their own? It's very handy having access to external i2c devices.
Yes... the pads are still in place.
by Bertus Kruger
Fri Apr 16, 2021 8:52 am
Forum: Current Version(3.51)
Topic: Board orientation and connection plugs.
Replies: 1
Views: 649

Re: Board orientation and connection plugs.

Hi... What version of the board do you have?

The enable pin in next to where the little capacitors(Coke cans) leads go into the board.