Search found 13 matches

by JuiceBox
Tue May 07, 2019 6:18 pm
Forum: Current Version(2.60)
Topic: External drivers
Replies: 9
Views: 1880

Re: External drivers

Correct Driver boards- https://imgur.com/a/el4Vtv6 Incorrect Driver Board - https://imgur.com/a/ux8LMiL You, like me , have incorrect driver boards. Mod went dark once I pointed it out and haven't heard anything from them since. 😕 IF (BIG IF) the board is correct and the silkscreen is what is wrong,...
by JuiceBox
Fri May 03, 2019 1:03 pm
Forum: Current Version(2.60)
Topic: Stepper Rotates Clockwise No matter what
Replies: 14
Views: 1672

Re: Stepper Rotates Clockwise No matter what

So are you going to be sending me new boards???
by JuiceBox
Mon Apr 22, 2019 8:32 pm
Forum: Current Version(2.60)
Topic: Stepper Rotates Clockwise No matter what
Replies: 14
Views: 1672

Re: Stepper Rotates Clockwise No matter what

No worries on the delay, thanks for getting back to me and sorry for the tone in my previous messages. I tend to write these things when I just spent a number of hours debugging things and I'm pretty heated. I probably should wait until I cool down before I write a message now that I think about it....
by JuiceBox
Mon Apr 22, 2019 12:45 pm
Forum: Current Version(2.60)
Topic: whats the difference
Replies: 3
Views: 521

Re: whats the difference

Just a heads up though, there are two different external driver boards floating around out there. I found out from someone else that theirs were different from mine.

His External Driver boards- https://imgur.com/a/el4Vtv6

My External Driver Board - https://imgur.com/a/ux8LMiL
by JuiceBox
Mon Apr 22, 2019 3:18 am
Forum: Version 2.51
Topic: DQ542 Drivers
Replies: 11
Views: 10684

Re: DQ542 Drivers

Hi,

Been having a ton of trouble with mine. What did you set your micro steps and amps to?
by JuiceBox
Mon Apr 22, 2019 3:15 am
Forum: Current Version(2.60)
Topic: Stepper Rotates Clockwise No matter what
Replies: 14
Views: 1672

Re: Stepper Rotates Clockwise No matter what

so..it's been a week... uhm... still dead in the water here...

bought new drivers just to be safe.... ugh.... It would really be great if I could get someone from Protoneer to tell me how to wire them up since the External Boards are incorrect. :(
by JuiceBox
Fri Apr 19, 2019 6:47 pm
Forum: Current Version(2.60)
Topic: Stepper Rotates Clockwise No matter what
Replies: 14
Views: 1672

Re: Stepper Rotates Clockwise No matter what

So I just had a bit of a breakthrough Ok so I've been on multiple forums trying to get answers to this. I had one guy who had his up and running send me a photo of their setup. His External Driver boards- https://imgur.com/a/el4Vtv6 My Exeternal Driver Board - https://imgur.com/a/ux8LMiL ...notice a...
by JuiceBox
Fri Apr 19, 2019 6:07 pm
Forum: Current Version(2.60)
Topic: Stepper Rotates Clockwise No matter what
Replies: 14
Views: 1672

Re: Stepper Rotates Clockwise No matter what

Wired as such, using CNCjs $4 =1 no motion $4 = 0, Very choppy, but no rotation RPi → Driver STEP →Pul - DIR → DIR - Enable → PUL +, DIR + Gnd → Not Connected Step Pin + 0V Dir pin = 0v Enable Pin = 0v Gnd Pin = 0v Everything reads zero volts whether moving or not. I used my power supply V- as my gr...